MagVISE EEPM-CIR Chucks
for Vertical Turning & 5-Axis

Advantages:

  • Reduce setup & part change-over time by 50% or more!
  • Machine freely on all 5 sides to reduce operations
  • Very uniform holding = No workpiece deformation

EEPM-CIR chucks are a powerful and fast workholding solution optimized for horizontal or vertical turning centers and 5-axis machining. Using magnetic workholding you can clamp/unclamp the part in only seconds. Reduce setup down-time to increase machine up-time. Control is included with chuck.


5-axis turbine blade machining

Circular setup for gear cutting

Pocket milling and face milling

Round part turning O.D. and I.D.
Model Dim. (O.D. x I.D. x H) No. Poles Holding Power Weight Control
EEPM-CIR500 19.7" x 0" x 2.75" 12 + 4 12,345 lbs. 229 lbs. C1
EEPM-CIR600 23.6" x 0" x 2.75" 12 + 4 17,636 lbs. 326 lbs. C2
EEPM-CIR800 31.5" x 9.84" x 3.34" 16 28,219 lbs. 665 lbs. C2
EEPM-CIR1000 39.4" x 9.84" x 3.34" 16 42,328 lbs. 1,038 lbs. C4
EEPM-CIR1250 49.6" x 19.68" x 4.33" 24 52,910 lbs. 1,825 lbs. C4
EEPM-CIR1500 59.0" x 19.68" x 4.72" 24 74,075 lbs. 2,921 lbs. C8
EEPM-CIR1600 64.2" x 19.68" x 4.72" 24 84,657 lbs. 3,322 lbs. C8
EEPM-CIR1800 71.6" x 31.49" x 4.72" 36 111,112 lbs. 5,048 lbs. C8
EEPM-CIR2000 80.7" x 39.37" x 5.11" 36 111,112 lbs. 5,489 lbs. C8

Induction & T-Slot Sliding Blocks

Use induction blocks to preserve the precision ground finish and prevent damage to the face of the chuck. Induction blocks to raise the workpiece above the surface of the magnet and permit machining 5 sides and thru-hole drilling.

Use T-Slot Sliding Blocks as adjustable work-stops for part alignment.

Part No. Description L W H
EEPM-SP spring loaded (2 piece set, 8mm screw) 1.89" 1.89" 1.41"
EEPM-SPF solid, machinable (8mm screw) 1.97" 1.97" 1.23"
EEPM-20T sliding T-slot for use with EEPM-SPF 4.72" 1.97" .78"
EEPM-30T sliding T-slot for use with EEPM-SP blocks 4.72" 1.97" 1.18"
EEPM-CIRIB120 induction block for CIR500 chuck 4.72" 1.97" .78"
EEPM-CIRIB170 induction block for CIR600 chuck 6.69" 1.97" .78"
EEPM-CIRIB245 induction block for CIR800 chuck 9.64" 1.97" .78"
EEPM-CIRIB335 induction block for CIR1000 chuck 13.18" 1.97" .78"
EEPM-CIRIB220 induction block for CIR500 chuck 8.66" 1.97" .78"
EEPM-CIRIB270 induction block for CIR600 chuck 10.62" 1.97" .78"